C1/C37) 1967 EARLY Cougar Sequencer Sequential Turn Signal kit and Flasher Can

Description: California Proposition 65: WARNING: This product has not been tested for chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov All parts are new aftermarket replacement parts manufactured by Cougars Unlimited LLC and come with a 2-year limited factory warranty. They are replacement parts to be used to replace the original Ford parts used in there sequencing tail light systems on models that originally came with sequencing tail lights. You are purchasing One C7WY-13A366-AS - Sequential turn signal system unit (Fully Compatible with LED or Incandescent bulbs)AndOne C7WY-13A366-CR - K7 TURN SIGNAL INDICATOR RELAY ELECTRONIC (LED or Incandescent bulbs)Replaces: Sequencer Flasher - Directional Relay - Stop Lamp Relay (Located on the rubber pad in the trunk) andThermal Flasher Can - (Located under the dash) Application: 1967 Ford Mercury Cougar EARLY Model - Made before 1/3/1967 PLEASE READ: To make sure you are purchasing the correct part look in the trunk of your Cougar, locate the rubber pad, and count how many parts are mounted on the rubber pad. If there are three parts on the rubber pad then your Cougar has a stop lamp relay, this indicates that you have an EARLY Model made before 1/3/1967 and you are purchasing the correct unit. (C7WY-13A366-AS) If there are two parts on the rubber pad then your Cougar does not have a stop lamp relay, this indicates that you have a LATE model made after 1/3/1967 and you are purchasing the incorrect part. Do not purchase this part. You will need to purchase a (C2 LATE Model) C7WY-13A366-BS.*NOTE: K7 INDICATOR RELAY ELECTRONIC 1967 Cougar - When converting to LED bulbs the indicator lights on the dash will stop working because the original thermal flasher will stop working because LED bulbs do not draw enough current to activate it. To solve this problem Cougars Unlimited LLC makes Electronic Flasher can replacements. They work with either LED or Incandescent bulbs.The Cougars Unlimited LLC C7WY-13A366-CR Electronic Turn signal Indicator relay is a functional replacement for the 3-Pin K7 thermal indicator relay found under the dash of the 1967 Cougar. Failure of this relay caused the dash light to pulsate dimly or not flash during normal turn signal operation. Included in this purchase. Cougars Unlimited LLC strongly recommends using WCCC1157RPR (Red for rear) LED bulbs and WCCC1157YPR (Yellow for front) LED bulbs. They have a built in current limiting diode. This stops the reverse current flow that causes sequential turn signal systems to malfunction. Included for free: USB flash drive with a scanned in copy of “Mercury Cougar Sequential Turn Signal and Emergency Flasher Systems” factory service manuals and troubleshooting guide. Extensive research has been put into the choosing of proper connectors, gauge of wires, industrial grade connectors and electronic components. They are nice! All aspects of the manufacturing process from design to testing are overseen by an electronic engineer with over 40 years of experience, as a result these units the most robust and reliable units on the market. Cougars Unlimited LLC manufactures sequential turn signal systems for 1967-1973 Cougar and 1965-1971 Thunderbird and 1968-1970 Mustang Shelby. Since 1981 Cougars Unlimited has been the source for the electronic sequencers used to replace the failure-prone mechanical motor driven turn signal sequencers. Member of the Cougar Club of America since 1981 and a founding member of the Cougar Club of New Mexico. 40 years of service / Thousands sold to satisfied customers Parts Chart BARGANSPOT (an eBay store) www.barganspot.com (All parts manufactured by Cougars Unlimited LLC) 1967 Cougar SEQUENCER – EARLY MODEL – C1) C7WY-13A366-AS (LED or Incandescent bulbs) SEQUENCER – LATE MODEL – C2) C7WY-13A366-BS (LED or Incandescent bulbs) K5 INDICATOR RELAY C67) - C7WY-13A366-BR K6 EMERGENCY WARNING RELAY under the dash - C66) C7WY-10B926-BR K7 INDICATOR RELAY ELECTRONIC – C37) C7WY-13A366-CR (* Required with LED bulbs) K10 EMERGENCY WARNING RELAY in the trunk - C9) C7WY-10B926-AR STOP LAMP RELAY – EARLY MODEL – C10) - C7SZ-13482-BR TURN SIGNAL SWITCH – WITH OUT TILT – C44) C7ZZ-13341-FR (*LED bulbs only) TURN SIGNAL SWITCH – WITH TILT – C47) C7ZZ-13341-ER (*LED bulbs only) HARNESS REPAIR KIT - EARLY MODEL C34) C7WY-13H366-AR HARNESS REPAIR KIT - LATE MODEL C32) C7WY-13H366-BR Front Turn Signal Bezel Harness pigtail (1 pair) C77) C8WB-13234-AR Copy 67 68 COUGAR TURN SIGNAL MANUAL PDF - C31A) Flash drive Dash to Engine Gauge feed W slide clip oil sender 289/302 - C58) C7DZ-14289-BR Dash to Engine Gauge feed W push on post oil 390/427/428 - C59) C7ZZ-14289-AR Dash to Engine Gauge feed W push on oil sender 289/302 C57) - C6DZ-14289-BR Dash to Engine Gauge feed W HD Black oil/water sender wires 390 - C39) C7GB-14289-AR XR7 "Alternator wiring harness" 289/302 (With Amp Meter) - C15) C7ZZ-14305-BR XR7 "Alternator wiring harness" 390 (With Amp Meter) (wo/TE) - C16) C7ZZ-14305-CR XR7 "Alternator wiring harness" 390 with ammeter - with TE - C80) C8WB-14305-ER Standard "Alternator wiring harness" 289 - C18) C7ZZ-14305-ER Standard "Alternator wiring harness" 390 (wo / Amp Meter) (wo / TE) - C17) C7ZZ-14305-DR Tilt Column Harness - C26) C7ZZ-3D568 Door Harness - All models - (One Pair) (R and L) - C22) C7WY-13A769-AR XR7 “Dash Panel to Headlight” Wiring Harness - C11) C7WY-14290-HR Standard “Dash Panel to Headlight” Wiring Harness - C12) C7WY-14290-JR *NOTE: K7 INDICATOR RELAY ELECTRONIC 1967 Cougar - When converting to LED bulbs the dash indicator lights will stop working because the original thermal flasher will stop working because LED bulbs do not draw enough current to activate it. To solve this problem Cougars Unlimited LLC makes Electronic Flasher can replacements. They work with either LED or Incandescent bulbs.*NOTE: TURN SIGNAL SWITCH – All turn signal switches sold by Cougars Unlimited LLC are for use with LED bulbs only. The reason for this is applicable vehicles are now over 50 years old the current that sequencing systems draw have greatly increased over time. This is because of the original wiring harnesses and connectors are deteriorating increasing the resistance. Higher the resistance the higher the current draw across the switch. The current is now so high on most vehicles that it exceeds the ratting of the switches, causing them to prematurely fail. The only solution is to convert to LED bulbs, they draw far less current. On vehicles that have converted to LED the turn signal switches are not failing. The only other solution is to replace the complete wiring harness which is expensive, and in most cases not possible. When converting to LED bulbs Cougars Unlimited LLC strongly recommends using WCCC1157RPR (Red for rear) LED bulbs and WCCC1157YPR (Yellow for front) LED bulbs. They have a built in current limiting diode. This stops the reverse current flow that causes sequential turn signal systems to malfunction.

Price: 399.95 USD

Location: Albuquerque, New Mexico

End Time: 2024-11-27T19:26:19.000Z

Shipping Cost: 0 USD