CC-65 AC/DC Current Clamp Meter Transducer for Digital Multimeter Oscilloscope w

Description: CC-65 AC/DC Current Clamp Meter Transducer for Digital Multimeter Oscilloscope with BNC Type Connector Hantek amp clamp AC/DC frequency range: Up to 20 kHz;hantek cc65 Effective Measurement Range: 20mA to 65A DC;The oscilloscope current probe is with Accurate circuit measurement and suitable for DSO;Hantek CC-65 amp clamp is Friendly in use: turn on, clamp it over a conductor, and get a reading;The current probe is with Output: BNC connector; Product Description Hantek AC/DC Current Clamp Up to 20 kHz Model Name: CC-65AC/DC frequency range: Up to 20 kHz;Effective Measurement Range: 20mA to 65A DC; The current clamp is a transducer, which allows your multimeter to measure current data and enable your oscilloscope to measure the current waveforms accurately. Brife Introduction When measuring the AC/DC Current with the Current Clamp, a multimeter or scope can directly measure the current up to 65 A , with a frequency up to 20KHz;In this method, there is no need to break a circuit or to affect the isolation to measure the current;The Current Clamp is not only available for the detection or monitor of the possibly existing creepage, but for the measurement with little gap using its extended jaws; However, it is necessary to turn the zero adjustment knobs on the clamp until the multimeter or scope reads zero. Load Resistance: 10kΩ Typical APPLICATION SAFETY The voltage of the conductor measured with the current clamp should be little than 300V DC or 240V rms AC; We are forbidden to measure the conductor whose insulation has break down or wear down. Key Features AC/DC frequency range: Up to 20 kHz; Effective Measurement Range: 20mA to 65A DC; Accurate circuit measurement and suitable for DSO; Friendly in use: turn on, clamp it over a conductor, and get a reading; Output: BNC connector; Take accurate current readings without breaking the circuit; Soft non-slippery over mold handle; Nice and accurate current clamp; HOW TO USE When connected with any multi-meter or a scope,connect the BNC connector of the clamp to a scope BNC connector;Set the power switch form “Off” to “ON” position, that is to set the multimeter range to 1mV/10mA or 1mV/100mA. Then, the green LED will be lighting, indicating that the clamp is switched on;when the current is not greater than 2 ampere ,please set the current clamp range to 1mV/10mA and set the multi-meter range to 200mV AC or 200 mV DC, which depends on the type of the current;Before measuring the DC current, it is needed to turn the zero adjustment knobs on the clamp until the multimeter reads zero. That means pushing down the zero adjustment knobs on the clamp until the multimeter reads zero. Then let go hold of the zero adjustment knobs.When using a scope,set DC coupled mode to measure DC current;Clamp the jaws around the current-carrying conductor and operate as above; APPLICATION NOTES When the current clamp range is set to 1mV/10mA, the actual current is ten times of the measured current whose unit is mA. For example, the measured current is 10 mV and The actual current of the current-carrying conductor is 10×10=100mA;When the current clamp range is set to 1mV/10mA, the actual current is ten times of the measured current whose unit is mA. For example, the measured current is 10 mV and The actual current of the current-carrying conductor is 10×10=100mA;In the case of DC current, the output is positive when the current flows from the upside to the underside of the clamp;In the case of DC current measurement, the current clamp can not possibly zero properly, due to the hysteresis effect. To eliminate this, open and close the jaws several times and then zero again. GENERAL SPECIFICATIONS Captured Conductor diameter: 9mm maximum Low Battery Indicator: Red LED lighting Operating Temperature: 0℃ to 50℃, 70% R.H. Storage Temperature: - -20℃~+70℃, 80% R.H. Battery type: 9V DC, NEDA 1604, 6F22, 006P Weight: 250 gram typical Dimensions: 195 mm (H) x 70 mm (W) x 33 mm (D) Output: 1m wire with a BNC connector Giftbox Package Included: current clamp*1; user manual*1 Add to Cart Add to Cart Customer Reviews 4.3 out of 5 stars 257 4.0 out of 5 stars 71 Price $108.90$108.90 $65.90$65.90 Channel 8channel 2channel Style Digital Power Source Battery Powered Color Blue Product Dimensions 3.94 x 8.27 x 1.97 inches; 8.82 ounces Country of Origin China Item Weight 0.25 Kilograms Shipping Fast shipping is very important for us. Our standard US shipping service is FREE. Your order will be shipped within 2-3 business days upon full payment received. Your order will be delivered within 2-3 business days after the handling time. We only ship to the confirmed PayPal address. We reserve the right to cancel any order for any reason at any time. We are not responsible for undeliverable addresses. Returns and payment We offer a 30 days return policy from checkout winning date. We allow only PayPal as payment methodFeedBack Your feedback very important to us, after you get your package and you are satisfied with our service please leave us positive feedback If you have any problem with your order / any questions please before leave any type of feedback For any questions, using eBay contact system Please visit our eBay store to check out other items for sale!Thank you for shopping at our store.

Price: 95.99 USD

Location: Bell Gardens, California

End Time: 2024-10-02T05:03:11.000Z

Shipping Cost: 0 USD